DIN 16962-5-2000
|
ID： |
5AF5D067A5714AEBBD8F9CA21C0D00B8 |
|
文件大小(MB)： |
0.52 |
|
页数： |
11 |
|
文件格式： |
|
|
日期： |
2013-7-3 |
|
购买： |
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
DEUTSCHE NORM April 2000,Pipe fittings and joint assemblies for,polypropylene (PP) pressure pipes,Part 5: General quality requirements and testing,DIN,16962-5,ICS 23.040.45 Supersedes,October 1999 edition.,Rohrverbindungen und Formstucke fur Druckrohrleitungen,aus Polypropylen (PP) - PP-H 100, PP-B 80 und PP-R 80 -,Teil 5: Allgemeine Qualitatsanforderungen, Prufung 加年8月士 §曾,In keeping with current practice in standards published by the International Organization for Standardization,(ISO), a comma has been used throughout as the decimal marker.,Contents,Foreword.,1 Scope,2 Normative references..,3 Concept and material designation ..,4 Material ..,5 Requirements .. ..,5.1 Form supplied..,5.2 Surface finish ..,5.3 Dimensions and tolerances ..,Page Page,1 5.4 Long-term hydrostatic pressure,resistance .. 3,2,6 Testing 4,2 6.1 Time of testing 4,2 6.2 Form supplied and surface finish . 4,6.3 Dimensions and tolerances 5,3 6.4 Long-term hydrostatic pressure,resistance 5,3 6.5 Certificate 6,3,Q Explanatory notes .. 6,3 Other relevant standards. 11,Foreword,This standard has been prepared by Technical Committee Fittings fur Druckrohre aus Thermoplasten of the,Normenausschuss Kunststoffe (Plastics Standards Committee).,Amendments,This standard differs from the October 1999 edition in that it has been editorially revised.,Previous editions,DIN 1692-5:1977-07; 1989-10, 1999-10.,ai 产一；-」 ?一-， ---， , /■ * L 7,All dimensions are in millimetres.,Continued on pages 2 to 11.,Translation by DIN-Sprachendienst.,In case of doubt, the German-language original should be consulted as the authoritative text.,. No part of this translation may be reproduced without the prior permission of,DIN Deutsches Institut fur Normung e.V., Berlin. Beuth Veriag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).,Ref. No. DIN 16962-5 : 2000-04,English price group 09 Sales No. 0109,06.01,Page 2,DIN 16962-5: 2000-04,/Mki-标准下载站,q,1 Scope,This standard specifies requirements and test methods for pipe fittings and joint assemblies for pressure pipes,made from polypropylene of types H 100, B 80 and R 80, as specified in DIN 16962-1 to DIN 16962-4 and in,DIN 16962-6 to DIN 16962-13. Individual requirements specified here may be superseded by technical delivery,conditions for particular applications.,NOTE: Any relevant European Standards which cover such applications shall also be observed.,2 Normative references,This standard incorporates, by dated or undated reference, provisions from other publications. These normative,references are cited at the appropriate places in the text, and the titles of the publications are listed below.,For dated references, subsequent amendments to or revisions of any of these publications apply to this,standard only when incorporated in it by amendment or revision. For undated references, the latest edition of,the publication referred to applies.,DIN 8077,DIN 8078,DIN 16962-1,DIN 16962-2,DIN 16962-3,DIN 16962-4,DIN 16962-6,DIN 16962-7,DIN 16962-8,DIN 16962-9,DIN 16962-10,DIN 16962-11,DIN 16962-12,DIN 16962-13,DIN EN 10204,DINEN ISO 12162,Polypropylene (PP) pipes - Dimensions,Types 1, 2 and 3 polypropylene (PP) pipes - General quality requirements and testing,Pipe joint assemblies and fittings for types 1 and 2 polypropylene (PP) pressure pipes -,Gusseted bends for butt welding - Dimensions,Pipe joint assemblies and fittings for types 1 and 2 polypropylene (PP) pressure pipes 一,Gusseted tees and branches produced by necking, for butt welding - Dimensions,Pipe joint assemblies and fittings for types 1 and 2 polypropylene (PP) pressure pipes 一,Bends formed from pipes, for butt welding - Dimensions,Pipe joint assemblies and fittings for types 1 and 2 polypropylene (PP) pressure pipes -,Adaptors for heated tool butt welding, flanges and sealing elements - Dimensions,Pipe joint assemblies and fittings for types 1 and 2 polypropylene (PP) pressure pipes 一,Injection-moulded elbows for socket welding - Dimensions,Pipe joint assemblies and fittings for types 1 and 2 polypropylene (PP) pressure pipes -,Injection-moulded tees for socket welding - Dimensions,Pipe joint assemblies and fittings for types 1 and 2 polypropylene (PP) pressure pipes -,Injection-moulded sockets and caps for socket welding - Dimensions,Pipe joint assemblies and fittings for types 1 and 2 polypropylene (PP) pressure pipes 一,Injection-moulded reducers and nipples for socket welding - Dimensions,Pipe joint assemblies and fittings for types 1 and 2 polypropylene (PP) pressure pipes -,Injection-moulded fittings for butt welding - Dimensions,Pipe joint assemblies and fittings for types 1 ……
……